We've unearthed this post about A Step-by-Step Guide to Installing a Bathtub listed below on the internet and felt it made good sense to discuss it with you on this site.
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as set in the brand-new one. Make sure you have qualified yourself for the job and also are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed job, it is better to consider using one before you start. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bathtub in your restroom if you have actually currently bought a new bathtub and also don't require to transform the plan of your previous water pipes.
Your tools and also material checklist ought to comprise the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to avoid pressure on the tub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly bothersome due to the limited gain access to that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bathtub in the required placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet port to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the water supply and also examine all joints as well as new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the tub should wait until the bathtub has been utilized a minimum of once as this will settle it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in area in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The former kind should be connected to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to permit the motion experienced when the tub remains in usage. The sealer can split rather very early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very taken with Installing A Bathtub and I hope you liked the entire blog post. Do you know about another individual who is looking into How to Install a Bathtub? Be sure promote it. I take joy in reading our article about Installing A Bathtub.
We're waiting, call!